tinyAVR Microcontroller Projects for the Evil Genius has 15 ratings and 1 review. CREATE FIENDISHLY FUN tinyAVR MICROCONTROLLER PROJECTS This. , English, Book, Illustrated edition: TinyAVR microcontroller projects for the evil genius / Dhananjay V. Gadre and Nehul Malhotra. Gadre, Dhananjay V. 18 Jan After covering the development process, tools, and power supply sources, tinyAVR Microcontroller Projects for the Evil Genius gets you working.

Author: Mikat Kazrami
Country: Bulgaria
Language: English (Spanish)
Genre: Life
Published (Last): 13 December 2018
Pages: 62
PDF File Size: 14.19 Mb
ePub File Size: 2.62 Mb
ISBN: 686-9-75982-630-5
Downloads: 89356
Price: Free* [*Free Regsitration Required]
Uploader: Shakajas

For example, a mouse requires a power supply for operation and it can use the USB power. Some of the images drawn with an LED pen and captured with a camera are shown in Figure Here, switch S2 is replaced tinhavr a potentiometer labeled POT1. A voltage regulator is an active component, and when you use this to provide a stable output voltage, it also consumes some tinyavr microcontroller projects for the evil genius. Books by Dhananjay Gadre.

The microcontroller used is the ATtiny microcontroller. Skip to content Skip to search. The ADC is used in the single conversion mode here.

Muhammad Alaa marked it as to-read Sep 23, These online bookshops told us they have this item: Click Finish, and you will see the main source file open and you can start writing your code. Evil Genius 1 – 10 of 38 books. It takes the readings tinyavr microcontroller projects for the evil genius the three ADC channels, one by one, and assigns them to the corresponding variables of the pwm array. In the tjnyavr mode, with increasing signal level at the input, more and more LEDs light up microcoontroller bottom to top.

The pen has two switches: Felix marked it as to-read Projectz 06, The candle flame sways randomly or so it seemsand sometimes the intensity of the flame seems to vary with air currents.

tinyAVR Microcontroller Projects for the Evil Genius

The latest version of AVR Studio can be downloaded from http: Depending upon the way the LED was connected to the pin, the LED could be turned on or off by setting the logic on the pin to “1” or “0”. Tinyavr microcontroller projects for the evil genius a primary battery with the same weight as a secondary battery can provide operating voltage for a longer time than the secondary battery can.


The lowest addresses in the program memory space are, by default, defined as the interrupt vectors. These are available on the links provided with each project.

However, it would take a program to shift the 16 bits of data onto the 16 output pins. However, the purpose of the mood lamp is to create ambient light of any required color to help you meditate or relax, or simply to set the ambient light depending upon your mood.

However, a high clock frequency also has a downside: It is primarily used for communication between the PC as the host and peripheral devices such as a camera, keyboard, etc. As soon as the mode is changed from discrete to continuous, the code exits the while loops. The microcontroller is programmed such that if the LED light is turned off with the help of switch S2the microcontroller enters a low-power operating mode — the power-down mode of operation — which tinyavr microcontroller projects for the evil genius the current consumption.

The rectifier should be suitably rated, keeping in mind the current requirements. The current requirement is mA, which is much more than a single pin of the microcontroller can supply.

The following illustration shows the block diagram of the ADC. Both the circuits are made on single-sided board. Most of the components can be ordered through Digikey or Farnell. The main clock can be selected to be any one of these through the fuse bits.

Add a tag Cancel Be the first to add a tag for this edition. They can be recharged several times in their usable lifetime and, therefore, are preferred prkjects primary batteries, although secondary batteries are more expensive. Vaishnavi Sundararajan did a great job of editing the manuscript at our end before we shipped each chapter to the editors.


tinyavr microcontroller projects for the evil genius

The lithium battery, on the other hand, uses a variety of chemical compounds, and depending upon these compounds, it has an open circuit terminal voltage between 1. This is because the batteries depend upon a chemical reaction to tinyavr microcontroller projects for the evil genius power and the chemical reaction is temperature dependent. Tinyl3V operating voltage range is between 1. These programs generally run in infinite loops and do not terminate. If the intensity of the LEDs is large enough, you can feel the ambient environment around you changing.

tinyAVR Microcontroller Projects for the Evil Genius™ – Inventors

The intensity control of LEDs is discussed in detail in the next section. Lisa marked it as to-read Nov 18, These projects can be built for fun as well as education. Let us take an example to illustrate the issue. Atmel AVR microcontroller — Amateurs’ manuals.

tinyAVR Microcontroller Projects for the Evil Genius

Rather than put microconntroller trademark symbol after every occurrence of a trademarked name, we use names in an editorial fashion only, and to tinyavr microcontroller projects for the evil genius benefit of the trademark owner, with no intention of infringement of the trademark.

However, things are quite different now. The power supply source and the regulation of the supply voltage are discussed in detail in a later section. However, if we want to make projects with a large number of LEDs, then we need microcontrollers with more pins.